Update LICENSE

LICENSE

@@ -0,0 +1,28 @@
+BSD 3-Clause License
+
+Copyright (c) 2025, Splatink
+
+Redistribution and use in source and binary forms, with or without
+modification, are permitted provided that the following conditions are met:
+
+1. Redistributions of source code must retain the above copyright notice, this
+   list of conditions and the following disclaimer.
+
+2. Redistributions in binary form must reproduce the above copyright notice,
+   this list of conditions and the following disclaimer in the documentation
+   and/or other materials provided with the distribution.
+
+3. Neither the name of the copyright holder nor the names of its
+   contributors may be used to endorse or promote products derived from
+   this software without specific prior written permission.
+
+THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
+AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
+IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
+FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
+DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
+SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
+CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
+OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
+OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.

readme.md

@@ -1,4 +1,4 @@
-A digital clock and thermomter/hydrometer written in Arduino for the Raspberry Pi Pico using an SH1106 OLED dispaly and a BME280 environment sensor
+A digital NTP clock and thermomter/hydrometer written in Arduino for the Raspberry Pi Pico using an SH1106 OLED dispaly and a BME280 environment sensor
 
 Pin definitions and display drivers (as long as the display is 128x64) can easily be changed in the code
 
@@ -8,4 +8,8 @@ The battery level is read by the battery going into a simple 10k resistor voltag
 
 The OLED display and BME280 share the same I2C lines into the Pico
 
-Pin definitions and display drivers (as long as the display is 128x64) can easily be changed in the code
+Pin definitions and display drivers (as long as the display is 128x64) can easily be changed in the code
+
+28/09/25 WARNING: This code has bugs and holes. It is the first piece of software ever written by me, and since then, I've (unfotunetly) given up programming. 
+I am not responsible for anything that happens if you use this neither do I care.
+If you want to run this, do so at your own risk and on an isolated IOT network.

src/main.cpp

@@ -16,8 +16,8 @@
 
 U8G2_SH1106_128X64_NONAME_F_HW_I2C u8g2(U8G2_R0, U8X8_PIN_NONE);
 
-const char* ssid = "Limbo";
-const char* password = "95H2O862U235@#";
+const char* ssid = "teo";
+const char* password = "teo";
 
 bool lpmode, debugmode;
 
@@ -25,9 +25,11 @@ WiFiUDP ntpUDP;
 NTPClient timeClient(ntpUDP, "gr.pool.ntp.org", 0, 1296000000);
 Adafruit_BME280 bme;
 
-void serialDebugInfo(float batteryVoltage, float batteryPrecentage, int wifiRSSI, int wifiStatus, const char* day, bool brightness, float temperature, float humidity, float pressure, bool disconnected)
+void serialDebugInfo(float firmwareVersion, float batteryVoltage, float batteryPrecentage, int wifiRSSI, int wifiStatus, const char* day, bool brightness, float temperature, float humidity, float pressure, bool disconnected)
 {
-	Serial1.print("Battery Voltage: ");
+  Serial1.print("Firmware Version: ");
+  Serial1.println(firmwareVersion, 1);
+  Serial1.print("Battery Voltage: ");
 	Serial1.println(batteryVoltage, 1);
 	Serial1.print("Battery Precentage: ");
 	Serial1.println(batteryPrecentage, 0);
@@ -375,7 +377,7 @@ void setup()
   {
     Serial1.setTX(0);
     Serial1.setRX(1);
-    Serial1.begin(9600);
+    Serial1.begin(115200);
     debugmode = true;
   }
 }
@@ -383,7 +385,7 @@ void setup()
 void loop()
 {
   static bool disconnected = false;
-  static int counter = 0; 
+  static int counter = 29; 
   timeClient.update();
 
   const char* day = getDay(timeClient.getDay());
@@ -401,7 +403,7 @@ void loop()
   if (debugmode == true && counter >= 30)
   {
     float pressure = bme.readPressure();
-    serialDebugInfo(batteryVoltage, batteryPrecentage, wifiRSSI, wifiStatus, day, brightness, temperature, humidity, pressure, disconnected); 
+    serialDebugInfo(2.2 ,batteryVoltage, batteryPrecentage, wifiRSSI, wifiStatus, day, brightness, temperature, humidity, pressure, disconnected); 
     counter = 0; 
   }
   counter++; 

updates.md

@@ -1,5 +1,9 @@
 **CHANGELOG:**
 
+2.2:
+* Changed baudrate to standard 115200 baud
+* Added a firmware version printout to serial
+
 2.1:
 * Added a serial debugging mode. This mode is activated if the BUTTON is held at bootup. Serial debugging info (variables) are output on GPIO0(TX) at 9600 baud every 30 seconds.
 * All functions are now called seperately and their return values placed in variables to be given to displayClocl() and serialDebugInfo()
@@ -59,4 +63,4 @@
 
 1.0:
 * Updated battery precentage calculator math to original (measurement - min) / (max - min) * 100
-* Created this updates.md file 
+* Created this updates.md file